Check Bolt connectivity when an aggregate metric changes
When a monitored total or average moves, get a fresh device connectivity check alongside the run report.
Trigger
Aggregate Metric Changed
Triggers when an aggregate metric (SUM/COUNT/AVG/MIN/MAX) changes in a Google Sheets spreadsheet. This trigger monitors an aggregate calculation on a target column (optionally filtered by a search column/value) and fires when the calculated result changes.
Action
Check Bolt device online status
Tool to check whether a specified bolt device is online. use when you need to verify device connectivity before sending commands (e.g., control signals). example: 'check if device bolt1234567 is online.'
Why this helps
A changing operational total can be hard to act on if checking the relevant device requires a separate manual step.
- Pair an aggregate change with a device connectivity check.
- See whether a specified Bolt device is online when a metric shifts.
- Keep the follow-up visible in Notis run reports.
Setup
Build it in a few focused steps.
- 1Connect Google Sheets and Bolt IoT once in the Notis portal.
- 2Create a new automation in Automations and give it a clear name.
- 3Tell Notis: when the monitored aggregate metric changes, check whether the specified Bolt device is online and report the status.
- 4Pick Aggregate Metric Changed as the trigger and choose where run reports should go.
- 5Test with one real metric change and review the report.
Questions about this workflow
Does Notis decide what counts as a concerning change?
The trigger fires when the monitored aggregate calculation changes. If you want a particular threshold or interpretation, include the decision rule in your instruction.
Will it turn a device on or off?
No. This workflow checks online status only.
When this happens · Trigger
Do this · Action
Supported Triggers and Actions
Notis builds workflows that link Google Sheets to Bolt iot. A trigger fires from one place; an action lands in another.
Google Sheets triggers
Bolt iot actions
Recurring trigger
Notis starts this workflow on a schedule, such as daily, weekly, or during business hours.
Analog Read
Tool to read the analog value from a specified pin on a bolt device. use when you need sensor readings (0–1023) after confirming the device is online.
Webhook trigger
Notis starts this workflow when an external tool or custom backend sends an HTTP request.
Bolt IoT Digital Write
Tool to set a digital pin high or low on a specified bolt device. use when controlling actuators or leds via digital output.
Aggregate Metric Changed
Triggers when an aggregate metric (SUM/COUNT/AVG/MIN/MAX) changes in a Google Sheets spreadsheet. This trigger monitors an aggregate calculation on a target column (optionally filtered by a search column/value) and fires when the calculated result changes.
Check Bolt device online status
Tool to check whether a specified bolt device is online. use when you need to verify device connectivity before sending commands (e.g., control signals). example: 'check if device bolt1234567 is online.'
Cell Range Values Changed
Triggers when values in a specified A1 range change in Google Sheets. This trigger monitors a specific cell or range of cells and fires when any values change.
Bolt IoT Digital Write
Tool to set a digital pin high or low on a specified bolt device. use when controlling actuators or leds via digital output.
Conditional Format Rule Changed
Triggers when conditional formatting rules change in a Google Spreadsheet. Detects when rules are added, updated, or removed. Uses snapshot-based diffing to detect changes between polls.
Bolt IoT Serial Read
Tool to read incoming serial data from a bolt device. use when you've initialized uart with serialbegin and need to retrieve serial data.
Data Validation Rule Changed
Triggers when data validation rules change (added/updated/removed) in a Google Spreadsheet. Uses snapshot-based diffing to detect changes between polls.
Bolt IoT Serial Write
Tool to send serial data to a bolt device. use when you need to transmit ascii data over uart after initializing uart with serialbegin.
Developer Metadata Changed
Triggers when developer metadata entries change (new/updated/removed) in a Google Spreadsheet. Uses snapshot-based diffing to detect changes between polls.
Bolt IoT Serial Write & Read
Tool to send serial data and read the response on a bolt device. use when you need to transmit ascii data over uart and capture its reply immediately.
Filtered Range Values Changed
Polling trigger that monitors Google Sheets filtered ranges for value changes. Uses snapshot-based diffing to detect when values matching a data filter change. Emits the matched values when changes are detected.
Connect any two apps with Notis in the middle.
Google Sheets and Bolt iot, or any other combination from 1,000+ integrations.
When this happens · Trigger
Do this · Action
Save your first hour today.
7-day trial of any paid plan, with 20$ of usage included.
No card. Works with personal or business Bolt iot.